|
聚醚醚酮,PEEK Witcom PEEK 2007/020东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123
13549213581 肖生
Witcom PEEK 2007/020
Polyetheretherketone
Witcom Engineering Plastics B.V.
Technical Data
Product Description
Article code KTA2007/351
General
Material Status • Commercial: Active
Literature 1 • Technical Datasheet (English)
Search for UL Yellow Card • Witcom Engineering Plastics B.V.
• Witcom PEEK
Availability • Europe
Additive • Lubricant
Features • Good Moldability • Lubricated
Processing Method • Injection Molding
Physical Nominal Value (English) Nominal Value (SI) Test Method
Density 1.55 g/cm³ 1.55 g/cm³ ISO 1183
Molding Shrinkage - Flow (0.118 in (3.00 mm)) 0.80 to 1.2 % 0.80 to 1.2 % ISO 2577
Water Absorption ISO 62
Saturation, 73°F (23°C) 0.40 % 0.40 %
Equilibrium, 73°F (23°C), 50% RH 0.20 % 0.20 %
Mechanical Nominal Value (English) Nominal Value (SI) Test Method
Tensile Stress (Break) 13100 psi 90.0 MPa ISO 527-2
Tensile Strain (Break) 1.5 to 3.0 % 1.5 to 3.0 % ISO 527-2
Flexural Modulus 1.09E+6 psi 7500 MPa ISO 178
Flexural Stress 21800 psi 150 MPa ISO 178
Impact Nominal Value (English) Nominal Value (SI) Test Method
Notched Izod Impact Strength 1.7 ft•lb/in² 3.5 kJ/m² ISO 180/1A
Unnotched Izod Impact Strength 17 ft•lb/in² 35 kJ/m² ISO 180/1U
Thermal Nominal Value (English) Nominal Value (SI) Test Method
Heat Deflection Temperature ISO 75-2/A
264 psi (1.8 MPa), Unannealed 311 °F 155 °C
RTI Imp (0.118 in (3.00 mm)) 356 °F 180 °C UL 746
Flammability Nominal Value (English) Nominal Value (SI) Test Method
Flame Rating (0.0315 in (0.800 mm)) V-0 V-0 ISO 1210
Glow Wire Flammability Index IEC 60695-2-12
0.0630 in (1.60 mm) 1760 °F 960 °C
Injection Nominal Value (English) Nominal Value (SI)
Drying Temperature 302 to 356 °F 150 to 180 °C
Drying Time 4.0 hr 4.0 hr
Suggested Max Moisture 0.050 % 0.050 %
Processing (Melt) Temp 716 to 770 °F 380 to 410 °C
Mold Temperature 320 to 392 °F 160 to 200 °C
Injection Rate Fast Fast
Back Pressure 36.3 to 145 psi 0.250 to 1.00 MPa
Injection Notes
Screw speed: 0.1 - 0.2 m/s
Injection pressure: Keep to a minimum
Hold pressure: Keep to a minimum
聚醚醚酮,PEEK Witcom PEEK 2007/020是东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123
13549213581 肖生
|
